x SuSE Linux 13.1-RELEASE x
x SuSE Linux 13.1-RELEASEx
SYSTEMD.SCOPE(5) systemd.scope SYSTEMD.SCOPE(5)
NAME
systemd.scope - Scope unit configuration
SYNOPSIS
scope.scope
DESCRIPTION
Scope units are not configured via unit configuration files, but are
only created programmatically using the bus interfaces of systemd. They
are named similar to filenames. A unit whose name ends in ".scope"
refers to a scope unit. Scopes units manage a set of system processes.
Unlike service units, scope units manage externally created processes,
and do not fork off processes on its own.
The main purpose of scope units is grouping worker processes of a
system service for organization and for managing resources.
systemd-run --scope may be used to easily launch a command in a new
scope unit from the command line.
See the New Control Group Interfaces[1] for an introduction on how to
make use of scope units from programs.
Note that, unlike service units, scope units have no "main" process:
all processes in the scope are equivalent. The lifecycle of the scope
unit is thus not bound to the lifetime of one specific process, but to
the existence of at least one process in the scope. This also means
that the exit statuses of these processes are not relevant for the
scope unit failure state. Scope units may still enter a failure state,
for example due to resource exhaustion or stop timeouts being reached,
but not due to programs inside of them terminating uncleanly. Since
processes managed as scope units generally remain children of the
original process that forked them off, it is also the job of that
process to collect their exit statuses and act on them as needed.
AUTOMATIC DEPENDENCIES
Implicit Dependencies
Implicit dependencies may be added as result of resource control
parameters as documented in systemd.resource-control(5).
Default Dependencies
The following dependencies are added unless DefaultDependencies=no is
set:
o Scope units will automatically have dependencies of type Conflicts=
and Before= on shutdown.target. These ensure that scope units are
removed prior to system shutdown. Only scope units involved with
early boot or late system shutdown should disable
DefaultDependencies= option.
OPTIONS
Scope files may include a [Unit] section, which is described in
systemd.unit(5).
Scope files may include a [Scope] section, which carries information
about the scope and the units it contains. A number of options that may
be used in this section are shared with other unit types. These options
are documented in systemd.kill(5) and systemd.resource-control(5). The
options specific to the [Scope] section of scope units are the
following:
OOMPolicy=
Configure the out-of-memory (OOM) killing policy for the kernel and
the userspace OOM killer systemd-oomd.service(8). On Linux, when
memory becomes scarce to the point that the kernel has trouble
allocating memory for itself, it might decide to kill a running
process in order to free up memory and reduce memory pressure. Note
that systemd-oomd.service is a more flexible solution that aims to
prevent out-of-memory situations for the userspace too, not just
the kernel, by attempting to terminate services earlier, before the
kernel would have to act.
This setting takes one of continue, stop or kill. If set to
continue and a process in the unit is killed by the OOM killer,
this is logged but the unit continues running. If set to stop the
event is logged but the unit is terminated cleanly by the service
manager. If set to kill and one of the unit's processes is killed
by the OOM killer the kernel is instructed to kill all remaining
processes of the unit too, by setting the memory.oom.group
attribute to 1; also see kernel documentation[2].
Defaults to the setting DefaultOOMPolicy= in systemd-system.conf(5)
is set to, except for units where Delegate= is turned on, where it
defaults to continue.
Use the OOMScoreAdjust= setting to configure whether processes of
the unit shall be considered preferred or less preferred candidates
for process termination by the Linux OOM killer logic. See
systemd.exec(5) for details.
This setting also applies to systemd-oomd.service(8). Similarly to
the kernel OOM kills performed by the kernel, this setting
determines the state of the unit after systemd-oomd kills a cgroup
associated with it.
RuntimeMaxSec=
Configures a maximum time for the scope to run. If this is used and
the scope has been active for longer than the specified time it is
terminated and put into a failure state. Pass "infinity" (the
default) to configure no runtime limit.
RuntimeRandomizedExtraSec=
This option modifies RuntimeMaxSec= by increasing the maximum
runtime by an evenly distributed duration between 0 and the
specified value (in seconds). If RuntimeMaxSec= is unspecified,
then this feature will be disabled.
Check systemd.unit(5), systemd.exec(5), and systemd.kill(5) for more
settings.
SEE ALSO
systemd(1), systemd-run(1), systemd.unit(5), systemd.resource-
control(5), systemd.service(5), systemd.directives(7).
NOTES
1. New Control Group Interfaces
https://www.freedesktop.org/wiki/Software/systemd/ControlGroupInterface
2. kernel documentation
https://docs.kernel.org/admin-guide/cgroup-v2.html
systemd 254 SYSTEMD.SCOPE(5)
Want to link to this manual page? Use this URL:
<http://star2.abcm.com/cgi-bin/bsdi-man?query=systemd.scope&sektion=5&manpath=>